AccuAir Control System Products

Shop By
AccuAir Control System Products Products Browse a collection of AccuAir Control System Products products en
AccuAir ENDO Service KitAccuAir ENDO Service Kit https://www.bagriders.com/media/catalog/product/cache/439c27ae68db3aa2c9619e8f902649db/a/c/accuair_endo_service_kit.png If you ever need to open up your AccuAir ENDO Tank to repair a faulty component, all of the hardware and o-rings must be replaced. If you don't end up replacing all of your hardware and o-rings after 'breaking the seal' you'll most likely have some pretty severe leaks. Includes: (16) End cap bolts (16) End cap bolt o-rings (2) End cap o-ring seals BR05825 USD 21.95 https://schema.org/NewCondition https://schema.org/InStock https://www.bagriders.com/vc/accuair-control-system-products/accuair-endo-service-kit.html$21.95 AccuAir ENDO-VT 5 Gallon Air Tank https://www.bagriders.com/media/catalog/product/cache/439c27ae68db3aa2c9619e8f902649db/a/a/aa_endo_raw_vt_5_1.jpg AccuAir's ENDO-VT 5 gallon air tanks take streamlined appearance to an entirely new level by integrating the solenoid valves and manifold directly into the air tank end caps themselves. Going for the cleanest air ride suspension setup out there? The ENDO tank from AccuAir is the way to go! The ENDO-VT represents AccuAir’s next generation of solenoid valve technology that includes VFC (variable flow control) in addition to D.O.T. approved fully filtered and rebuildable ffPTC (fully-filtered push-to-connect) fittings. This 5-gallon version of AccuAir's ENDO tank has a 2-corner valve-cap on each end providing 4-corner control. No need for any additional manifolds or valves for your air ride suspension setup! If you're happy with your current valve / manifold setup on your air ride system, you can just pick up the ENDO-T version that doesn't come with the valves and functions like a normal air tank. Features: AccuAir now includes the solenoid valves and air tank in an all in one easy to mount package The 5 gallon ENDO tank from AccuAir is available with 4 corner valve configurations AccuAir is including built-in VFC (variable flow control) adjusters that allow you to adjust of the speed of each corner and each direction individually. Your vehicle now has the ability to move up and down level from front to rear. No need for flow controls! The built-in PTC fittings on AccuAir's ENDO tank are DOT approved and rebuildable The ENDO tank features filtered ports which help to eliminate the risk of debris-induced valve problems In AccuAir's tests, they actuated the ENDO tank's valves for over 10 million cycles The ENDO tank's modular and bolted construction eliminates the possibility of leaky welds and makes disassembly possible for upgrades AccuAir's ENDO tank's extruded internal rails house embedded mounting locations along the tank providing clampless attachment of ENDO-Mount brackets and accessories The ENDO tank is the only DOT Approved, aluminum air tank for air suspension. Certified to 200psi and tested to 1324psi burst pressure The Endo tank includes black nickel plated fittings and a built-in 400 psi blow-off valve to ensure safe use AccuAir's included ENDO-QR quick release mounting system allows easy installation and even easier air management assembly outside the vehicle AccuAir made mounting easy by allowing the ENDO tank to be back or bottom mounted Like most of AccuAir's products, the ENDO tank is made in the USA with a limited lifetime warranty Love this ENDO tank from AccuAir but wish they had a smaller version? They do! Check out the AccuAir Endo Aluminum 3 Gallon Air Tank Includes: AccuAir ENDO-VT Tank Pigtail valve harnesses Black, nickel plated hex plugs Quick release feet & mounting hardware BR05719 USD 899.95 https://schema.org/NewCondition https://schema.org/InStock https://www.bagriders.com/vc/accuair-control-system-products/accuair-endo-vt-5-gallon-tank-4-corner-raw.html
AccuAir ENDO-T 5 Gallon Air TankAccuAir ENDO-T 5 Gallon Air Tank https://www.bagriders.com/media/catalog/product/cache/439c27ae68db3aa2c9619e8f902649db/a/a/aa_endo_raw_t_5_2.jpg Features: The ENDO tank's modular and bolted construction eliminates the possibility of leaky welds and makes disassembly possible for upgrades AccuAir's ENDO tank's extruded internal rails house embedded mounting locations along the tank providing clampless attachment of ENDO-Mount brackets and accessories The ENDO tank is the only DOT Approved, aluminum air tank for air suspension. Certified to 200psi and tested to 1324psi burst pressure The Endo tank includes black nickel plated fittings and a built-in 400 psi blow-off valve to ensure safe use AccuAir's included ENDO-QR quick release mounting system allows easy installation and even easier air management assembly outside the vehicle AccuAir made mounting easy by allowing the ENDO tank to be back or bottom mounted Like most of AccuAir's products, the ENDO tank is made in the USA with a limited lifetime warranty Love this ENDO tank from AccuAir but wish they had a smaller version? They do! Check out the AccuAir ENDO-T Aluminum 3 Gallon Air Tank Includes: AccuAir ENDO-T Tank Black, nickel plated hex plugs Quick release feet & mounting hardware BR05711 USD 449.95 https://schema.org/NewCondition https://schema.org/InStock https://www.bagriders.com/vc/accuair-control-system-products/accuair-endo-t-5-gallon-tank-raw.html$449.95
AccuAir ENDO-T 3 Gallon Air TankAccuAir ENDO-T 3 Gallon Air Tank https://www.bagriders.com/media/catalog/product/cache/439c27ae68db3aa2c9619e8f902649db/a/a/aa_endo_raw_t_3_1.jpg Features: The ENDO tank's modular and bolted construction eliminates the possibility of leaky welds and makes disassembly possible for upgrades AccuAir's ENDO tank's extruded internal rails house embedded mounting locations along the tank providing clampless attachment of ENDO-Mount brackets and accessories The ENDO tank is the only DOT Approved, aluminum air tank for air suspension. Certified to 200psi and tested to 1324psi burst pressure The Endo tank includes black nickel plated fittings and a built-in 400 psi blow-off valve to ensure safe use AccuAir's included ENDO-QR quick release mounting system allows easy installation and even easier air management assembly outside the vehicle AccuAir made mounting easy by allowing the ENDO tank to be back or bottom mounted Like most of AccuAir's products, the ENDO tank is made in the USA with a limited lifetime warranty Love this ENDO tank from AccuAir but wish they had a bigger version? They do! Check out the AccuAir ENDO-T Aluminum 5 Gallon Air Tank Includes: AccuAir ENDO-T Tank Black, nickel plated hex plugs Quick release feet & mounting hardware BR05715 USD 399.95 https://schema.org/NewCondition https://schema.org/InStock https://www.bagriders.com/vc/accuair-control-system-products/accuair-endo-t-3-gallon-tank-raw.html$399.95
AccuAir Bulkhead KitAccuAir Bulkhead Kit https://www.bagriders.com/media/catalog/product/cache/439c27ae68db3aa2c9619e8f902649db/a/c/accuair_audi_b8_bulkhead_kit.jpg This bulkhead kit from AccuAir contains all the fittings necessary to run your 4 bag lines out the chassis of your car to the suspension. Includes: (4) 3/8" PTC bulkhead fittings (8) 3/8" PTC swivel elbows BR01814 USD 153.95 https://schema.org/NewCondition https://schema.org/InStock https://www.bagriders.com/vc/accuair-control-system-products/accuair-bulkhead-kit.html$153.95 AccuAir VU4 4-Corner Manifold (NPT) https://www.bagriders.com/media/catalog/product/cache/439c27ae68db3aa2c9619e8f902649db/a/c/accuair_vu4_manifold_npt_base_1b.jpg AccuAir’s VU4 Manifold has become an industry standard. Backed by a lifetime warranty and solid reliability, it’s hard to beat. This NPT version of the VU4 eliminates the standard 3/8” PTC ports and allows you to get creative by using your own fittings. The NPT VU4 is perfect for those interested in unique hardline setups. This electronic solenoid valve unit inflates and deflates up to four (4) individual air springs. Although the VU4 may look pretty, it’s durable enough to survive the harsh under vehicle environments. The wires from each of the solenoids route to a single weatherproof connector, eliminating typical loose wires. This manifold can be used with most managements and system configurations. Includes: VU4 4-Corner Manifold with 1/4" NPT Ports VU4 to AccuAir ECU plug-n-play harness (6) 1/4" NPT to 3/8" PTC male straights (6) 1/4" NPT plugs Mounting hardware BR01111 USD 549.95 https://schema.org/NewCondition https://schema.org/InStock https://www.bagriders.com/vc/accuair-control-system-products/accuair-vu4-manifold-npt.html
AccuAir e-Level Sensor Linkage and Hardware https://www.bagriders.com/media/catalog/product/cache/439c27ae68db3aa2c9619e8f902649db/s/n/snesor_linkage_and_hardware.jpg This sensor linkage and hardware pack is for the current AccuAir e-Level sensors. The Air Lift 3H Sensor Linkage and Hardware is a direct replacement. The linkage is a slightly different length so you may need to cut it down. BR01751 USD 38.95 https://schema.org/NewCondition https://schema.org/InStock https://www.bagriders.com/vc/accuair-control-system-products/accuair-e-level-sensor-linkage-and-hardware.html
AccuAir e-Level Sensor Plastic Arm https://www.bagriders.com/media/catalog/product/cache/439c27ae68db3aa2c9619e8f902649db/u/p/updated-e-level-sensor-arm.jpg AccuAir designed these replaceable e-Level sensor arms to snap under excessive load which prevents the sensor itself from being damaged. These plastic sensor arms are only compatible with the latest version of e-Level sensors (purchased after 2013). BR01750 USD 16.95 https://schema.org/NewCondition https://schema.org/InStock https://www.bagriders.com/vc/accuair-control-system-products/accuair-e-level-sensor-plastic-arm.html
AccuAir e-Level Sensor https://www.bagriders.com/media/catalog/product/cache/439c27ae68db3aa2c9619e8f902649db/a/a/aa-sensrot-120.jpg This sensor from AccuAir is a replacement for a broken or malfunctioning e-Level sensor. The Air Lift 3H sensor is a direct replacement. The sensor arm is a slightly different shape so you may need to adjust your linkage. BR03344 USD 109.95 https://schema.org/NewCondition https://schema.org/InStock https://www.bagriders.com/vc/accuair-control-system-products/accuair-e-level-sensor.html
AccuAir VU4 to ECU HarnessAccuAir VU4 to ECU Harness https://www.bagriders.com/media/catalog/product/cache/439c27ae68db3aa2c9619e8f902649db/e/c/ecu_to_vu4_harness.jpg This one foot harness connects the AccuAir VU4 manifold to any of AccuAir's ECUs. It is the same harness that is included with the purchase of a VU4. BR00086 USD 49.95 https://schema.org/NewCondition https://schema.org/InStock https://www.bagriders.com/vc/accuair-control-system-products/accuair-vu4-to-ecu-harness.html$49.95 AccuAir Pigtail Valve Harness https://www.bagriders.com/media/catalog/product/cache/439c27ae68db3aa2c9619e8f902649db/v/a/valve_harness.jpg The AccuAir Pigtail Valve Harness is the same as the one included when purchasing an AccuAir system. One end has a connector for the back of any AccuAir ECU and the other end can be wired to a manifold or valves of your choice. Be sure to check out the valve harness pinout before starting your install. BR02012 USD 49.95 https://schema.org/NewCondition https://schema.org/InStock https://www.bagriders.com/vc/accuair-control-system-products/accuair-pigtail-valve-harness.html
AccuAir e-Level Sensor HarnessAccuAir e-Level Sensor Harness https://www.bagriders.com/media/catalog/product/cache/439c27ae68db3aa2c9619e8f902649db/e/-/e-level_sensor_harness.jpg This e-Level Sensor Harness is a direct replacement for the harness that's included with the e-Level+ system. The harness is 20ft long for the front sensors and 16ft long for the rear sensors. This harness will also work for older e-Level TouchPad and e-Level Rocker Switch systems. BR00989 USD 181.95 https://schema.org/NewCondition https://schema.org/InStock https://www.bagriders.com/vc/accuair-control-system-products/accuair-e-level-sensor-harness.html$181.95



